Missions

CASE ARCHIVE

All missions

37VISIBLE / 37 TOTAL
CASE001
DEBUGFoundational≈ 12 MIN

The SPI Device Never Responds

Compare /CS at both endpoints and trace the physical route before changing firmware.

SPI · ConnectivityNot started
CASE002
DESIGNBeginner-friendly≈ 10 MIN

5 V Sensor, 3.3 V MCU

Two resistors. Four requirements. Design a sensor interface that meets all of them.

Analog · Voltage dividersNot started
CASE003
REVIEWFoundational≈ 10 MIN

Where Does the Current Come Back?

A clock trace crosses a gap in its reference plane. Follow the other half of the circuit.

PCB layout · Return pathsNot started
CASE004
DESIGNBeginner-friendly≈ 12 MIN

Your GPIO Can't Drive This

Switch a 12 V relay from a 3.3 V command, including reset and turn-off.

MOSFETs · Inductive loadsNot started
CASE006
DEBUGIntermediate≈ 15 MIN

It Works Until the Motor Starts

A controller resets at startup. Correlate the rail and current captures.

Power · BrownoutNot started
CASE007
DEBUGIntermediate≈ 15 MIN

The I²C Device Has Disappeared

A new harness, a faster bus, and no reply. Separate protocol from analog edge timing.

I²C · Pull-upsNot started
CASE008
BRING-UPFoundational≈ 15 MIN

First Power-On

Inspect the new assembly, bound the supply current, and establish a powered baseline.

Lab practice · Power railsNot started
CASE010
DEBUGIntermediate≈ 15 MIN

The Buck Converter Won't Behave

The supply passes at light load. Find what changes at the required current.

Power · MagneticsNot started
CASE011
DESIGNFoundational≈ 12 MIN

Your Shunt Is Measuring the Copper Too

Separate force current from sense voltage and release a layout within its error budget.

Current sensing · Kelvin connectionsNot started
CASE012
DESIGNFoundational≈ 12 MIN

A High Level That Isn't High Enough

The bench accepts a HIGH. Check guaranteed voltage margins and qualify an interface across supply corners.

Digital logic · Level compatibilityNot started
CASE013
DESIGNFoundational≈ 15 MIN

Someone Reversed the Power Plug

Protect the board from a reversed plug while meeting forward loss, gate stress and thermal limits.

Power entry · Reverse polarityNot started
CASE014
DESIGNIntermediate≈ 15 MIN

More Copper, or a Different Component?

Qualify a regulator, package and board layout across low-line regulation and high-line thermal limits.

Power · Regulator thermalsNot started
CASE015
DESIGNFoundational≈ 15 MIN

A 10 µF Capacitor That Isn’t 10 µF Here

Turn nominal capacitance into a worst-case effective value using supplied tolerance, bias, temperature and aging data.

Components · Capacitor deratingNot started
CASE016
DESIGNFoundational≈ 12 MIN

It Turns On Before the Firmware Does

Keep an active-high load disabled while the MCU pin floats at reset, then hand control to firmware without a glitch.

Startup safety · Hardware defaultsNot started
CASE017
DESIGNIntermediate≈ 15 MIN

The Board Is Off, but the Signal Is Still On

Contain a live clock crossing into an unpowered board without sacrificing the powered timing requirement.

Power sequencing · Back-poweringNot started
CASE018
DESIGNFoundational≈ 12 MIN

The Button Pressed Itself

Give a remote switch a defined electrical state, reject a cable transient, and validate contact bounce without missing a real press.

Digital inputs · Noise and debounceNot started
CASE019
DEBUGIntermediate≈ 15 MIN

The ADC Works Until You Change Channels

Explain channel-memory error and choose sampling/discard settings that meet accuracy without breaking scan throughput.

ADC · Acquisition settlingNot started
CASE020
REVIEWIntermediate≈ 15 MIN

The Protection Part Is in the Wrong Place

Follow a connector strike through the copper and release a TVS placement, routing and return path supported by characterized captures.

ESD · Protection layoutNot started
CASE021
DEBUGIntermediate≈ 15 MIN

Two Outputs Are Fighting

Correlate an intermediate logic level with supply current, then qualify a shared open-drain line against current and rise-time limits.

Digital interfaces · Bus contentionNot started
CASE022
BRING-UPFoundational≈ 15 MIN

The Prototype Cannot Be Programmed

Separate target power from debugger voltage reference, repair the header contract and establish a conservative first SWD connection.

Bring-up · SWD accessNot started
CASE023
DEBUGFoundational≈ 12 MIN

The Scope Invented the Ringing

Compare ground-lead captures, shrink probe loading and loop area, and qualify the waveform before changing the PCB.

Measurements · Probe artifactsNot started
CASE024
DESIGNIntermediate≈ 15 MIN

It Only Fails at the Corners

Combine source, path, dropout, reference and resistor limits so a nominal 3.3 V rail remains valid at every supplied corner.

Power · Worst-case analysisNot started
CASE025
REVIEWIntermediate≈ 15 MIN

It Changes Layers. What About the Return?

Identify the reference before and after a signal via, then provide a local return transition between unlike plane nets.

PCB layout · Reference transitionsNot started
CASE026
DEBUGIntermediate≈ 15 MIN

The Motor Shares Your Sensor's Ground

Correlate a sensor error with motor return current, measure the reference shift and separate high-current and measurement returns.

Grounding · Shared impedanceNot started
CASE027
DESIGNFoundational≈ 15 MIN

The Battery Must Last Longer

Time-weight active and sleep currents, include every always-on load and qualify a one-year battery architecture.

Low power · Energy budgetsNot started
CASE028
DEBUGIntermediate≈ 15 MIN

The MOSFET Is Getting Hot

Correlate gate and drain waveforms, separate conduction from switching loss and qualify the complete electrical/thermal path.

Power switching · LossesNot started
CASE029
REVIEWIntermediate≈ 15 MIN

Keep the Switch Node Away From My Signal

Find the pulsed commutation loop, control switch-node copper and route feedback from a quiet point away from the aggressor.

PCB layout · Switching powerNot started
CASE030
DEBUGFoundational≈ 12 MIN

The ADC Reading Makes No Sense

Trace a stable analog value through the fitted divider, actual ADC reference and raw code before blaming the sensor.

ADC · Reference and scalingNot started
CASE031
DESIGNIntermediate≈ 15 MIN

Stop the Inductive Kick

Balance MOSFET voltage stress, coil-current decay and pulse energy with a complete turn-off clamp network.

Inductive loads · Clamp designNot started
CASE032
DESIGNIntermediate≈ 15 MIN

One Supply, Two Rails

Choose a two-rail topology, preserve loaded-current margin and enforce the required startup order within a fixed heat budget.

Power architecture · Rail sequencingNot started
CASE033
REVIEWIntermediate≈ 18 MIN

Would You Release This PCB?

Separate requirement-level release blockers from unusual but controlled details using electrical, transient and mechanical evidence.

PCB review · Release readinessNot started
CASE034
DESIGNIntermediate≈ 16 MIN

Make This Measurement Useful

Map a millivolt sensor into the ADC range while respecting amplifier guarantees, signal bandwidth and interference rejection.

Analog front ends · Gain and filteringNot started
CASE035
REVIEWIntermediate≈ 16 MIN

How Many Grounds Does This ADC Need?

Apply device-specific ground guidance by controlling local pin connection, functional partition and analog/digital return-current loops.

Mixed signal · ADC groundingNot started
CASE036
REVIEWIntermediate≈ 15 MIN

The Regulator Regulates the Wrong Point

Move a regulator's feedback takeoff past loaded copper, route it quietly and prove the load voltage across current.

Power integrity · Remote sensingNot started
CASE037
DEBUGFoundational≈ 14 MIN

The Connector Has Power, but the IC Doesn’t

Measure a remote supply under load, total cable/contact/trace resistance and qualify both voltage and thermal margins.

Power delivery · Voltage dropNot started